Marvel Series 8 Mark 1 Manual
Posted : admin On 03.01.2021Vertical Tilt-Frame Band Saws
- Mark 1 Computer
- Marvel Series 8 Mark 1 Manual Pdf
- Marvel Series 8 Mark Iii
- Marvel 8 Mark 1
- Marvel Series 8 Mark 1 Operating Manual
Mark 1 Computer
Marvel Series 8 Mark 1 Universal Vertical Metal Cutting Band Saw – Parts Manual – 20 pgs Marvel Series 9 High Speed Ball Bearing Hack Saw – Instruction & Parts Manual – 49 pgs Marvel Series 9A High Speed Heavy Duty Automatic Hack Saw – Parts Manual – 14 pgs. 2016 honda 225 hp 4 stroke outboard manual. Stansbury, Mark:: 1943: Service Manuals: Marvel Metal Band Saw No. 8 Parts List: 16: Tyson, Neil. Marvel Series 6 and 9 Highspeed Heavy Duty Hacksaw.
- All-Mechanical Design
- Cast Iron Construction
- Metal Cutting
- Large Adaptable Work Table
Marvel Series 8 Mark 1 Manual Pdf
Related products
18' x 22'
18' x 12.75'
50-450 fpm infinitely variable speed drive system.
Allows blade speed to be adjusted from operator's control station.
0 - 140 lbs. infinitely variable direct reading scale balance beam.
Work area 24.25' x 33'; table height 34.5'; four machined T-slots accept .625' (15.5 mm) T-Bolts.
Column and blade tilt up to 45° right and left of vertical; work always stationary. Built in protractor.
Maximum opening 18'. Jaws can be shifted to either right or left side of blade. Jaws are 6' high, 12' wide.
Adjustable stops can be pre-set to stop advance and return of blade and to stop motor at any location within the 18' travel of the blade.
Built in with Flood system, available with added optional drop lubrication system. Controlled by on-off selector switch at operator's station. Tank capacity 21 gallons.
Washes chips from hard-to-get-at places reducing clean-up time.
Together with blade wipers and flood coolant keep blade teeth free of chips.
Guides are stationary and can be rotated to present new guiding surface to the blade. Upper and lower guides have preloaded carbide-faced back-up blocks to support back edge of the blade.
14' 6' Long x 1' Wide x .035' Thick. One Welded-Edge Band Blade is furnished with each machine.
Main; 5 H.P., 1800 RPM, totally enclosed fan cooled. Coolant Pump; 1/8 H.P. enclosed motor-built-in integrally.
If ordering the 575 volt machine, it will be wired for 480 volt operation and a transformer will be provided with the machine.
A Phase-A-Matic phase converter is shipped with the machine and a 40 AMP service is required.
Column 6” longer than standard, providing increased vertical capacity to 28” at vertical position and 17” high at 45°.
10” high x 12” wide in place of standard jaws provided with machine. Do not permit miter cutting.
In place of standard jaws provided with machine. One Front Jaw and one Rear Jaw, both mitered 45°, 10” high x 12” wide.
Modification of standard column to add 3° forward approach angle, for increased efficiency in cutting of structural materials. Note: Changes horizontal capacity to 17”.
Modification of standard High Column to add 3° forward approach angle. Note: Changes horizontal capacity to 16.75”.
Marvel Series 8 Mark Iii
120 – 1080 fpm (36 – 329 m/min); main motor changed to 10 H.P., totally enclosed, fan cooled. Only available in 460-3-60 volt machine order.
Drop Lubrication System. (Requires compressed air connection 60-120psi) SUPPLEMENTARY EQUIPMENT UPON REQUEST.
Marvel 8 Mark 1
5’0” LONG, with five ball bearing rollers, 2.5” diameter, spaced on 12” centers, two stands, one end stop, and mounting bracket.
5’ 0” LONG, five ball bearing rollers, 2.5” diameter, spaced on 12” centers, one stand, attached to the first section dead roller.
First Section Dead Roller Conveyor Free Standing
5’ 0” LONG, with five ball bearing rollers, 2.5” diameter, spaced on 12” centers, two stands, and one end stop.
5’ 0” LONG, with five ball bearing rollers, 2.5” diameter, spaced on 12” centers, with one stand.
First Section Dead Roller Conveyor with Manual Length Gauge
Marvel Series 8 Mark 1 Operating Manual
10’ 0” LONG, ten ball bearing rollers, 2.5” diameter, spaced on 12” centers, includes Dead Stop, Tilting Type Gauge; manually operated.
5’ 0” LONG, five ball bearing rollers, 2.5” diameter, spaced on 12” centers. Equipped with gauge rail and measuring tape extensions.
Marvel series 8 Mark 1 vertical [url=band saw[/url]. Next to the hand wheel is the carriage feed worm gear. The operating manual says to check and fill the reservoir annually. It doesn't really give a good description of the desired oil level. Filling it completely as insinuated causes oil to run out around the shaft. Does anyone know how much oil they want? Since the worm is on top only the gear is in the bath unless the reservoir is actually 'full'. The exploded parts view shows no seal around the shaft.
Thanks,